Rentals
-
125 CFM ELECTRIC – ELECTRIC AIR COMPRESSORS
FULLY COMPUTERIZED
TEFC, IP55, degree of protection electric motors;
Automatic starters with phase and sequence failure detection;
Lubricated air-end;
Low maintenance costs;
Low oil consumption;
Coolers are on the top of the machine, improves heat recovery at customer’s facilities;
Modern design products;
High efficiency electric motors;
Thermostatic valve for working temperature control;
24V Command panel.
Operational SettingsOperation method – load/unload
Remote/local
Auto restart
Maintenance time to air filter, oil filter and air/oil separator, oil and main motor grease
Pressure and temperature units
Starts per hour
Error MessagesMain motor and fan motor overloaded
Phase fault or incorrect sequence
Emergency
High pressure
High temperature
Pressure and temperature sensor
AdvantagesLow noise level
Low Speed
Foam coated steel cabinet for noise reduction
Low discharge temperatureOversized cooling system
Longer oil and oil separator life time
Compressor prepared to handle higher ambient temperatures
Discharge temperature around 10°C above the ambient. -
125 CFM ELECTRIC WITH LIFTING RACK – ELECTRIC AIR COMPRESSORS
FULLY COMPUTERIZED
TEFC, IP55, degree of protection electric motors;
Automatic starters with phase and sequence failure detection;
Lubricated air-end;
Low maintenance costs;
Low oil consumption;
Coolers are on the top of the machine, improves heat recovery at customer’s facilities;
Modern design products;
High efficiency electric motors;
Thermostatic valve for working temperature control;
24V Command panel.
Operational SettingsOperation method – load/unload
Remote/local
Auto restart
Maintenance time to air filter, oil filter and air/oil separator, oil and main motor grease
Pressure and temperature units
Starts per hour
Error MessagesMain motor and fan motor overloaded
Phase fault or incorrect sequence
Emergency
High pressure
High temperature
Pressure and temperature sensor
AdvantagesLow noise level
Low Speed
Foam coated steel cabinet for noise reduction
Low discharge temperatureOversized cooling system
Longer oil and oil separator life time
Compressor prepared to handle higher ambient temperatures
Discharge temperature around 10°C above the ambient. -
AFTEK HEAT TREAT CONSOLE
AFTEK is the sole remaining manufacturer of resistor controlled welding machines in the USA. In 1977, Big 4 Manufacturing introduced their innovative Series 77 Control, and the features introduced then remain at the heart of the AFTEK design: Edge-wound coils for better heat dissipation (thus better current control) and rotary switches for current selection.
AFTEK and Big Four grids have been used to build nuclear power plants, to build and repair US Navy ships, for piping and vessels and with the exclusive Demand Pulse MIG, the thinnest sheet metal for food handling equipment, computer cases, aluminum boats.
One of the oldest welding technologies combined with one of the newest electronic switches makes an unbeatable combination for the toughest welding jobs
-
AIRMAN 185 CFM – DIESEL AIR COMPRESSORS
The Airman air compressors are super-quiet and super-efficient. Manufactured by MMD Equipment, their ultra-quiet air compressors are designed for today’s demands. They’re extremely reliable, which helps reduce downtime and maintenance. Just as important, their superior designs meet environmental concerns and are fuel-efficient, light and well-balanced. Their larger tool compartments hold 90-lb. breakers, various tools and hoses.
Other features include the drainage of the engine oil and water to the outside of the machine and hand-operated compressor oil and fuel drains so that no tools are required. In addition, new external oil/air separator filter and cartridge-type fuel filter reduce service time and cost and side-by-side radiator and oil cooler are more efficient and easier to clean.
You can download a PDF of an example of the type of Airman air compressor that may be rented from R.J. Kates.
-
AIRMAN 400 CFM – DIESEL AIR COMPRESSORS
The Airman air compressors are super-quiet and super-efficient. Manufactured by MMD Equipment, their ultra-quiet air compressors are designed for today’s demands. They’re extremely reliable, which helps reduce downtime and maintenance. Just as important, their superior designs meet environmental concerns and are fuel-efficient, light and well-balanced. Their larger tool compartments hold 90-lb. breakers, various tools and hoses.
Other features include the drainage of the engine oil and water to the outside of the machine and hand-operated compressor oil and fuel drains so that no tools are required. In addition, new external oil/air separator filter and cartridge-type fuel filter reduce service time and cost and side-by-side radiator and oil cooler are more efficient and easier to clean.
You can download a PDF of an example of the type of Airman air compressor that may be rented from R.J. Kates.
-
ARCON STUDHORSE 1200
The Arcon Studhorse 1200 welds up to 1200A for up to 3/4″ (19mm) full base studs, headed or threaded, in an 80lb unit Studhorse welder. It can weld steel, stainless and aluminum.
Some of its features are a low open circuit voltage of down to 8V, corrosion protection, runs on 30A slow blow fuse, and can be powered by 70KVA or 60KWA generator.
-
ArcReach® Heating System
Take Control of Weld Preheating With an ArcReach® Heating System
Weld preheating methods like flame and resistance send projects out of control:
They’re expensive
They’re time-consuming
They increase safety risksArcReach® Heating Systems put you back in control. This induction heating equipment uses alternating electromagnetic currents to generate heat in workpieces, so welders can do their own preheating quickly and safely.
-
BP-2
The BP-2 is a sturdy, smooth running positioner that will handle the loads and heavy demands of production MIG and intricate TIG welding.
POSITIONERS AND TURNING ROLLERS – R.J. Kates carries a variety of stands for pipe turning and supports for your welding needs.
-
BUG-O WELDER & TURNING ROLLERS
The Bug-O welding and cutting tools uses speed controlled rollers to turn pipe or other rounded material while the welding or cutting operation is performed.
A remote foot switch allows hands-free run and stop control. In addition, a “forward/stop/reverse” switch with potentiometer allows for step less speed adjustment. An 8-slot turntable provides for quick mounting and holding of a fixture.
-
Cables & Accessories
From 30 Amp. 110 Volt extension cords to 500 Amp welding leads to various hoses we have all your cable requirements covered. We have 10’s of thousands of feet of cables and hoses with dozens of your standard fittings and plugs. And if not we do not have exactly what you’re looking for we can custom make any adapter needed to get what you need.
As just a sampling, we have 1/4″, 3/8″, and 1/4″ air hose with quick disconnects; 1/0, 2/0, 3/0, and 4/0 weld cable with connectors; 1/4″ and 3/8″ gas hoses; and 2/4, 4/4, 6/4, 8/4/ and 10/4 sow cable.
From the weekend warrior working in his garage to the large projects that require 50 plus welders, we can pull from our tens of thousands of feet of cable and hundreds of accessories to make your rental package complete.
Our accessories include remote controls both wired and wireless, regulators, carbon arc torches, MIG guns, TIG torches, gas hoses, flexible goosenecks, and various carts and racks just to name a few!
Call us with you rental needs – equipment and accessories – we would be happy to help you!
-
CATERPILLAR X Q 200
The MMD PowerPro 25 features:
Standby Power: 250 kVA/200kW
Prime Power: 227.5 kVA/182kW
Fuel Capacity: 350 gals.
Operating Wgt: 11,660 lbs -
COBRAMATIC PRO
The Cobramatic Pro is a push-pull wire feed system. Its compact design allows it to go into tight spaces, including through a ship’s porthole. -
HOBART HANDLER 140
The Handler 140 can run these wires: .023 –.035″ mild steel or stainless steel, .030 –.035″ flux-cored, and .030″ aluminum. -
HOUGEN PORTABLE HMD505/508 AND HMD904 MAGNETIC-BASE DRILLS
HOUGEN PORTABLE HMD505/508 PDF AND HMD904 PDF MAGNETIC-BASE DRILLSThe new HMD508 portable magnetic drill (as displayed on the left) is a rugged, high powered drill for general fabrication and high production environments. The HMD508 features a two speed gear box with a new higher speed of 450 and 750 RPM for use with Copperhead™ carbide cutters. Additional features include: a patented quill feed arbor system for smooth cuts and minimal maintenance, positive slug ejection, and a two stage magnet which engages full power when the motor is turned on. The HMD508 also includes a gravity feed coolant bottle and carrying case.
The HMD904 is lightweight, compact, powerful and versatile, making it the drill of choice for general fabrication. Designed for the down and dirty job of making holes. The HMD904 is assembled with a hex drive spindle mounting, for fast and easy change out of drill arbor and accessories. The male hex mates to the drill arbor and is held in place by two set screws. To disengage the arbor, loosen the set screws and pull the arbor away from the motor spindle. The HMD904 also features rear-mounted, accessible controls and side-to-side reversible feed handles.
-
HYPERTHERM MAXPRO 200
The Hypertherm MaxPro 200 combines fast cutting speeds and quick process changes maximize productivity, allowing the fastest cut speeds in its class. -
HYPERTHERM POWERMAX 105
The Hypertherm Powermax 105 is a handheld-mechanized plasma system for cutting or gouging metal from 1 1/4″ to 2″.